Your Newly Finished Floor

A minimum of 24 hours is recommended before returning to the residence. Providing good ventilation will minimize the odor and help the floor finish cure faster. You can generally walk on the floor after 24 hours. However, you should use your floors with care for the first two weeks after application. The more gentle you are on the floor during this time, the more satisfaction you will get from your floors for years to come. Furniture – Allow two to three days before placing furniture on the floor. Do not drag or slide the furniture into place. Install Safeglides Felt Floor Protectors on furniture legs before replacing furniture. Carpets – Allow two to three weeks before putting carpets or rugs on the floor. If covered prematurely, finishes may discolor. Cleaning – Do not use water or any cleaning substances on the floor for the first two to three weeks.

Preventive Maintenance

Preventive Maintenance may be the most important factor in determining the longevity of your wood floor finish.

  • Place walk off mats in entry ways and near sink areas to minimize the amount of dirt and water that comes in contact with your floor.
  • Check your chair legs and other pieces of furniture and attach Safeglides® Felt Floor Protectors to all furniture that will come in contact with your wood floor.
  • Keep high heel shoes in good repair. Heels that have lost their protective cap can cause little indentations in any floor surface, even concrete!
  • Keep pet claws trimmed.
  • Do not over-water plants. Soil, fertilizers, and plant foods may have chemicals in them that could damage your Glitsa finish.
  • Soft rubber (shoe soles, toy wheels, etc.) will leave marks on the floor. Most of these marks can be rubbed out, but should be avoided if possible.

Wood Floor Maintenance

Simple steps can be taken to maintain the beauty and luster of your new Glitsa finished floors. Dust Mop – Use Glitsa’s untreated mop with Dust Pad on your floor regularly. This will keep the sand and grit off of your floor that may cause premature wear. Throw rugs that are cleaned on a regular basis are recommended in front of your kitchen sink and at each outside door. Cleaning – Wipe up food and other spills immediately using a dampened (not soaking wet) Cleaning Pad on the Glitsa Mop or paper towel. Regular cleaning should be done with Glitsa Clean™ which is specially formulated to clean your Glitsa finished floor. Follow directions on the bottle for correct application. Glitsa Clean™ is available through your flooring contractor. No Waxing – Glitsa finished floors should never be waxed. Do not use oils or waxes, or cleaners that have these properties, on your Glitsa finish. If wax or other treatments are applied, recoating may not be possible. Recoat – As your floor begins to show wear and does not clean easily with Glitsa Clean™, recoating is recommended. Glitsa Aerosol is available for minor repairs or touch up for the Gold Seal System. Contact your hardwood flooring professional when recoating becomes necessary. Know your Floor – Know what products were used to finish and clean your wood floor. Keep track of the dates (month/year) that the floor was installed, finished, refinished and/or repaired. Remember the company name of your floor installer and finisher. When moving, leave the above information in the home for the next homeowner.

Gold Seal Aerosol Directions for Use

Glitsa Gold Seal Touch-Up Aerosols

Glitsa Gold Seal Touch-Up Aerosols are the ideal touch up products for small areas with light scratches. This product is most effective on areas of less than one square foot. Glitsa touch-up aerosols are intended to rejuvenate the surface appearance of small worn areas. For larger or areas with excessive wear, consult a professional.

 

Directions For Use

If spraying over a recently coated surface, be sure to test an inconspicuous area to ensure no adverse affects.

  1. Make sure surface is free of contaminants (oils, wax, grease, etc.).
  2. Lightly prepare surface with fine sandpaper (220 grit or finer). NOTE: This product is not intended for use on vertical surfaces.
  3. Following surface preparation, thoroughly wipe the area clean to ensure that any dust created by the surface preparation is removed. Do not use solvents or commercially prepared tack rags.
  4. Protect surrounding areas from over spray.
  5. For best results, use only when the product and surface to be treated are between 60° – 80° F (16° – 27° C).
  6. SHAKE CAN vigorously for at least one minute after rattle or mixing ball is heard, to ensure uniformity of sheen and prevent clogging.
  7. Provide ventilation to the area being worked in, but prevent direct air flow (fans, vents, etc.) over the surface being sprayed.
  8. Multiple, thinly misted coats are recommended. Do not attempt to achieve final desired appearance in one or two heavy coats which could lead to wrinkling, peeling or uneven sheen. Allow to dry thoroughly (2-3 hours) between coats.
  9. Point opening of spray buttons towards surface, holding can 18 – 24 inches from area to be coated.
  10. Press spray button firmly. Use rapid overlapping motion while spraying.
  11. If clogging develops, turn spray button 1/4 turn. If clogging persists, remove and clean spray button only. DO NOT STICK OBJECTS INTO CAN. Gently replace spray button with twisting motion and exit hole pointing away from you.
  12. To clean spray button for future use, turn can upside down and press spray button until no more coating comes out.
  13. Discard empty container in accordance with local regulations. DO NOT place in home garbage compactor.
  14. If additional or more detailed instruction is required, please contact our Technical Service Department, Monday through Friday from 7am – 4pm (Pacific) at (800)444-7833.

 

EXTREME DANGER!

VERY FLAMMABLE LIQUID AND VAPOR. VAPOR MAY CAUSE FLASH FIRE. IRRITANT. POISON. VAPOR HARMFUL.

CONTENTS UNDER PRESSURE

See Other Cautions on Back Panel

RISQUE EXTRÊME!

 

LA LIQUIDE ET LA VAPEURE SONT TRÈS INFLAMMABLE. LE CONTENUE PEUT S’ENFLAMMER.

IRRITANT et POISON

LE CONTENU EST SOUS PRESSION

L’évêché Autres Prudences sur le Panneau de Dos.

 

Warning! This product contains a chemical known to the State of California to cause birth defects or other reproductive harm.

 

Attention! Ce produit contient un produit chimique connu dans l’État de Californie pour causer des malformations congénitales ou d’autres troubles de la reproduction.

 

 

Glitsa Gold Seal aerosols de reparation.

Glitsa Gold Seal aérosols de reparation sont les produits idéaux pour des rayures légères. Ce produit est plus efficace pour une surface de moins d’un pied carré. Aérosols de reparation Glitsa sont prevua rajeunir l’aspect de la surface de petits endroits usés. Pour les grandes surfaces ou avec une usure excessive, consultez un professionnel.

 

Conseils À Suivre

Si la pulvérisation sur une surface récemment revêtu, ne oubliez pas de tester un endroit discret pour se assurer qu’aucun des effets néfastes.

1. Assurez-vous que la surface n’a pas de contaminants (huiles, cires, graisses, etc.).

2. Préparer la surface légèrement avec du papier abrasif fin (grain 220 ou plus fin). NOTE: Ce produit n’est pas destiné à être utilisé sur des surfaces verticales.

3. Après la préparation de surface, essuyez soigneusement la zone propre à assurer que la poussière créée par la préparation de surface est enlevé. Ne pas utiliser de solvants ou chiffons adhésifs commerciale.

  1. Protégez les alentours de pulvérisation excessive.

5. Pour de meilleurs résultats, utilisez uniquement lorsque le produit et de la surface à traiter sont entre 60 ° – 80 ° F (16 ° – 27 ° C).

6. Agiter vigoureusement pendant au moins une minute après hochet ou la balle de mélange est entendu, pour assurer l’uniformité de la brillance et éviter le colmatage.

7. Assurer une ventilation à la zone exploitée en, mais empêcher l’écoulement de l’air directe (ventilateurs, évents, etc.) sur la surface à peindre.

8. Plusieurs couches minces sont recommandés. Ne essayez pas d’atteindre aspect final souhaité dans une ou deux couches lourds qui pourrait conduire à des rides, desquamation ou brillance inégale. Laisser sécher complètement (2-3 heures) entre les couches.

9. Pointer l’ouverture du bouton de pulvérisation vers la surface et tenir 18 – 24 cm de la zone à revêtir.

10. Appuyez sur le bouton de pulvérisation fermement. Utilisez une mouvement chevauchement rapide pendant la pulvérisation.

11. Si une obstruction se développe, tournez le bouton de vaporisation 1/4 de tour. Si la colmatage persiste, enleve le bouton de pulvérisation et le nettoyer. Ne pas mettre aucun material dans la bidon. Replacez délicatement le bouton de pulvérisation avec un mouvement de torsion et le trou de sortie pointant loin de vous.

12. Pour nettoyer le bouton de pulvérisation pour une utilisation future, son tour peut l’envers et le bouton de pulvérisation de presse jusqu’à ce que aucunpulvérisation sort.

13. Jeter le contenant vide conformément à la réglementation locale. Ne mettez pas dans un compacteur de déchets.

14. Si l’instruction supplémentaire ou plus détaillée est nécessaire, se il vous plaît communiquer avec notre service technique, du lundi au vendredi de 7 heures-16 heures (PST) au (800)444-7833.