Infinity II


Glitsa Infinity II is a low-VOC, single-component, oil-modified waterborne polyurethane floor finish. Infinity II is intended for use in residential and light commercial applications where a rich, warm appearance is desired. This single-pack wood floor finish has excellent flow, leveling and dry time and is available in Gloss, Semi-Gloss, Satin and Matte sheens. Infinity II does not require an additional crosslinker to achieve a scratch- and scuff-resistant finish with lasting durability. Infinity II depends on air oxidization to develop crosslinking.

  • Single-Component
  • No waste
  • 100% Urethane formula provides tough, durable finish
  • Optional crosslinker, Infinity Crosslink™, for faster hardness
  • Rich color, no need for color sealer
  • Excellent adhesion
  • Self-sealing system
  • Apply 1-2 coats of TruSeal under Infinity II over white oak to prevent tannin pull
Packaging: Gallon
VOC: Compliant
Coverage Rate: 500 – 600 sq ft per gallon
Dry To Touch: 1 – 1.5 hours
Dry To Recoat: 3 – 5 hours
Color: Amber
Application Method: Roller, Pad, T-Bar
Product Code: Gloss: 270098.80 • Semi-Gloss: 270098.50 • Satin: 270098.30 • Matte: 270098.15

DOWNLOADS:

Can be used with...

Can be applied over:

  • Itself (Infinity II)
  • Truseal
  • Glitsa Sealer

Can be applied under:

  • Glitsamax2

Systems

  • 3 coats Infinity II
  • 1 coat TruSeal + 2 to 3 coats Infinity II
  • 2 coats Infinity II + 1 coat GlitsaMax 2
  • 2 coats Glitsa Sealer + 1 to 2 coats Infinity II for a hybrid system
  • Over white oak: 2 coats TruSeal + 1 to 2 coats Infinity II

Application Instructions

Surface Preparation

Natural wood floors:

  • Sand to 100-120 grit using NWFA approved methods.
  • Screen with a 100-120 grit screen.
  • Remove all sanding dust from the floor by thoroughly vacuuming and tacking with a Glitsa Tack Mop.
  • At this time a Glitsa waterborne sealer or Infinity II can be applied to the wood surface. See sealer or finish directions for proper application and dry times.

 

Stained floors:

  • Sand to 100-120 grit using NWFA approved methods.
  • Screen with a 120-150 grit screen.
  • Remove all sanding dust from the floor by thoroughly vacuuming and tacking with a Glitsa Tack Mop.
  • Refer to directions on Glitsa stains for procedures and dry times.
  • Stained floors can be sealed with Glitsa TruSeal waterborne sealer. See sealer directions for proper application and dry times.

 

Note: It is the contractor’s responsibility to ensure the stain is thoroughly dry prior to coating with waterborne finishes.

Due to seasonal expansion and contraction of wood floors, white lines may appear over dark-stained floors.

 

Application Instructions:

Three coats of Infinity II, or one coat of TruSeal waterborne sealer and two coats of Infinity II, are recommended to achieve a durable, scuff resistant finish. High humidity, or low temperatures will extend dry times. Make sure to have indirect ventilation while applying Infinity II. Always strain waterborne finishes that have been stored in partially full containers.

 

Shake Infinity II for 15 seconds to ensure even distribution of flattening agents. Allow 10 – 15 mins for foam generated from shaking to dissipate before coating.

 

Apply Infinity II by using a lightweight T-bar. Make sure to use a new, lightly water-dampened applicator.

 

Start by pouring a 3” – 5” puddle of Infinity II with the grain of the wood, from wall-to-wall. Using the snowplow method, pull the Infinity II with the grain of the wood, from wall-to-wall. Use a cut-in pad or a T-bar to feather out turns.

 

Maintain a 3” – 5” puddle at all times, as this will help to ensure even coverage, and a uniform final appearance.

 

When Infinity II has dried to the touch, ventilate premises, while maintaining temperatures of at least 60° F (15.6°C). Optimum air quality is achieved through aggressive ventilation.

 

Allow Infinity II to dry 3 – 5 hours before additional coats are applied.

 

Once dry, abrade with a conditioning pad and 180 – 240 grit or finer sanding strips. Vacuum carefully and tack with a clean, water-dampened, Glitsa Tack Mop.

 

For additional coats follow previous application instructions.

 

Apply no more than two coats in a 24-hour period.

 

For Professional Use Only.

Read Safety Data Sheet (SDS) and Label Precautions before using this product.

Physical Properties

Waterborne TruSeal Pro  Infinity II GlitsaMax 2 Bare
Resin System Acrylic Urethane/Acrylic Urethane Polycarbonate Polycarbonate
Crosslinker n/a n/a Aziridine (Optional) Isocyanate Isocyanate
Cast (in can) Milky White Translucent/slight amber Translucent/slight amber Translucent Translucent
Clarity (when dry) Clear Clear Clear Clear Clear
Catalyst Ratio n/a n/a n/a 8.8 fl oz per Gallon 8.8 fl oz per Gallon
Pot Life** n/a n/a n/a 4 hours 4 hours
Solids by Weight 32.7% 30.4% 29.0% 30% (Mixed) 33.2% (Mixed)
Viscosity (#2 Zahn – seconds) 16-17 sec 40 sec 28-32 sec n/a n/a
Viscosity (#4 Ford – seconds) n/a n/a n/a 26-30 sec 26-30 sec
Flash Point (deg F.) >200 >200 >200 >200 >200
Pounds/Gallon 8.7 8.6 8.7 8.7 8.8
Dry Time to Touch*** 1-1.5 hours 1-2 hours 1-1.5 hours 2-3 hours 2-3 hours
Recoat Time 3-4 hours 3-5 hours 3-5 hours 5 hours 5 hours
Full Cure n/a 7-10 days 7-10 days 7-10 days 7-10 days
Sq.Ft. Coverage/Gallon 400-600 450-550 500-600 350-450 350-450
VOC grams/liter < 275 < 275 < 275 < 275 < 275
Sheen* – Gloss n/a 80 80 n/a n/a
Sheen* – Semi-Gloss n/a 50-55 50-55 50-55 n/a
Sheen* – Satin n/a 30-35 30-35 30-35 n/a
Sheen* – Matte n/a 15-20 15-20 n/a n/a
Sheen* – Ultra Matte n/a 15-20 15-20 10-15 n/a
Sheen* – Bare n/a n/a n/a n/a <5

*60 Degree Gloss Meter
**Increased temperatures will reduce pot life.
***@70 deg F, 50% RH

You may also like…