Lite Scent


Gold Seal Lite Scent is a one-component, precatalyzed, crystal-clear coating designed for use over Glitsa Sealer, Bacca or MultiKote. Lite Scent offers superior wear resistance, excellent adhesion and can be recoated after an overnight dry (depending on weather conditions), thereby eliminating the 90-day wait period between coats of regular Gold Seal finish.

  • One-Component
  • Only one topcoat recommended
  • Can recoat over itself, or Gold Seal, after 48 hours if an extra coat is desired. If recoating to repair, extended dry times may be required.
  • Do not apply over bare wood or stain
  • Only use over conversion varnish coatings
  • Excellent adhesion
  • Superior clarity
  • Excellent wear resistance due to its flexibility and scratches clear
Packaging: Quart, Gallon, 5-Gallon Pail
VOC: Compliant
Coverage Rate: 300 – 400 sq ft per gallon
Dry To Touch: 4-5 Hours
Dry To Recoat: 48 Hours
Color: Clear
Application Method: Brush, Roller, Mop, T-Bar
Product Code: Gloss: 651768.00 • Semi-Gloss: 651769.00 • Satin: 651770.00 • Matte: 651771.00

DOWNLOADS:

Can be applied over...

  • Bacca
  • Glitsa Sealer
  • MultiKote

Systems

  •  Glitsa Sealer or Bacca and 1 Lite Scent for a traditional, natural Swedish look that shows grain definition.
  • 2 Glitsa Sealer or Bacca and 1 Lite Scent for a higher build look.
  • 1 or 2 coats MultiKote and 1 Lite Scent for a high build system that has sheen before the topcoat.

Application Instructions

Allow Bacca or Glitsa Sealer to dry thoroughly (follow label instructions for seal coat) before applying Lite Scent. When dry, the seal coat should be lightly sanded with a well-used screen, 100 grit or finer. Note: Using new screens between coats will result in scratches showing through the final finish. If the screen seems to load up from sanding, allow additional time to dry before continuing. Vacuum thoroughly. If tacking is required, use alcohol, lacquer thinner or water only, on a clean cloth. (Do not use paint thinner or commercially prepared tack rags.) Have adequate ventilation while tacking. Allow to dry completely before proceeding.

 

Prior to application, turn off all pilot lights, heaters, air conditioners, and all other ignition sources. Since vapors may travel, prevent build up by ventilating areas of the job not being treated.

 

Lite Scent should be stirred well in the can before pouring into a clean plastic container. For best results, room temperature should be between 60° – 70° F during application. Wear a NIOSH/MSHA approved respirator to protect from organic vapors and formaldehyde when applying Lite Scent.

 

During winter months, warm temperature must be achieved then shut off heat. During application, it is important to provide adequate ventilation while preventing air movement (windows, doors and refrigerator exhausts) directly across the surface of the Lite Scent finish, as this will cause the coating to dry too quickly causing brushmarks and lack of flow. Provide indirect ventilation during application to achieve adequate air exchanges.

 

Avoid direct sunlight on the area being coated by covering windows where necessary. Hot sun will heat the wood and make the Lite Scent finish dry too fast to allow full flow or could cause bubbles in the finish.

 

Lite Scent should be applied freely with a Glitsa brush, or a lambswool applicator (new lambswool applicators may leave lint in finish). Lite Scent covers 350-400 sq. ft. per gallon. Follow the grain of the wood from wall-to-wall, being sure not to work or brush the material too much or apply too thinly, which could cause the Lite Scent to set up too quickly and not allow full flow. In hot, dry climates, Glitsa Retarder may be added to Lite Scent to lengthen open time and aid flow. Follow instructions on Retarder label. Note: Excess retarder will reduce the solid content of Lite Scent and lengthen dry time. Wrinkling of the final coat may result if any or all previous applications are not thoroughly dry, or if screened too deeply.

 

Once finish is dry to the touch (approximately four hours, depending on weather conditions), immediately open doors and windows to ventilate area, which will also aid the curing of the finish. Allow 24 hours to dry before allowing light traffic on floors.

 

Recoat: When the Lite Scent finish begins to show wear, or if the recommended cleaning procedure fails to clean the floor, recoating may be necessary. Minor repairs may be made with Lite Scent Aerosol. To prepare the floor for recoat, tack with a high grade lacquer thinner. Hand sand or screen floors with fine grit sandpaper or a used screen. Carefully vacuum up all dust, then follow instructions for application. Note: Adding Fusion bonding additive to Glitsa Lite Scent may help alleviate any possible adhesion issues in questionable recoats. Floors contaminated with waxes or oils should be resanded.

 

Clean brushes immediately after applying finish. Wash brushes twice in a high grade of lacquer thinner only. Soak brush in clean, fresh, lacquer thinner overnight, then dry thoroughly before using.

 

Use floors with care for the first 2-3 weeks after application. Do not cover or use water on floors during this first 2-3 week period.

 

For Professional Use Only.

Read Safety Data Sheet (SDS) and Label Precautions before using this product.

Product Properties

Conversion Varnishes Bacca Glitsa Sealer Gold Seal Lite Scent MultiKote
Cast Slightly Amber Amber Clear Clear Pale Amber
Clarity (in can) Semi-Transparent Clear Translucent Translucent Clear
Catalyst Ratio 14 fl oz per Gallon 6 fl oz per Gallon N/A – Precatalyzed N/A – Precatalyzed 4.8 fl oz per Gallon
Pot Life 24 hours** 24 hours** n/a n/a 24 hours**
Solids by Weight 40% 45% 20% 20% 39-40%
Viscosity (#2 Zahn – seconds) 23 sec 26 -30 sec 34 – 38 sec 34 – 38 sec 32 sec
Flash Point (deg F.) 51 38 48 – 60 49 – 61 54
Pounds/Gallon 7.87 8.03 7.09 – 7.17 7.24 – 7.41 7.70 – 7.79
Dry Time to Touch*** 4-5 hours 1-2 hours 4-5 hours 4-5 hours 1-2 hours
Recoat Time Overnight 2-4 hours After 90 days 48 hours 4-6 hours
Full Cure 60-90 days 60-90 days 60-90 days 60-90 days 7-10 days
Sq.Ft. Coverage/Gallon 300  – 350 300  – 350 350 – 400 350 – 400 300 – 400
VOC grams/liter 549 (includes hardener) 541 (includes hardener) 670 – 695 680 – 719 560-566 (includes hardener)
Sheen* – Gloss n/a n/a >90 >90 >85
Sheen* – Semi-Gloss n/a n/a 40-45 40-45 50-55
Sheen* – Satin n/a n/a 32-36 32-36 28-33
Sheen* – Matte n/a n/a 18-22 18-22 18-22

*60 Degree Gloss Meter
**Increased temperatures will reduce pot life.
***@70 deg F, 50% RH

You may also like…