Can be applied under
- Glitsa Poly 500 series
- GlitsaMax 2
- Infinity II
Quick Dry Sealer
Glitsa Quick Dry Sealer is an oil-modified polyurethane sealer designed for residential and commercial hardwood floor applications. Quick Dry Sealer is designed for use under Glitsa Poly 500 Series or any Glitsa waterborne finish.
- MFMA Approved
- Quick Dry
- 3 to 4 hours to recoat
- Easy to Apply
- No waste
- Formulated for reduced yellowing
Packaging: Quart, Gallon, 5-Gallon Pail
VOC: Max 550 grams per liter
Coverage Rate: 500 – 600 sq ft per gallon
Dry To Touch: 2 hours
Dry To Recoat: 3-4 hours
Color: Amber
Application Method: Brush, Roller, T-Bar, Pad
Product Code: 500949.00
VOC: Max 550 grams per liter
Coverage Rate: 500 – 600 sq ft per gallon
Dry To Touch: 2 hours
Dry To Recoat: 3-4 hours
Color: Amber
Application Method: Brush, Roller, T-Bar, Pad
Product Code: 500949.00
DOWNLOADS:
Systems
- 1 coat Quick Dry Sealer and 2 to 3 coats of Poly 500 Series
- 1 coat Quick Dry Sealer and 2 to 3 coats of any Glitsa Waterborne Finish for a hybrid system
Application Instructions
Surface Preparation:
Natural wood floors:
- Sand to 100-120 grit using NWFA approved methods
- Screen with a 100-120 grit screen.
- Remove all sanding dust from the floor by thoroughly vacuuming and tack with a Glitsa Tack Mop.
- At this time a first coat may be applied.
Stained Floors:
- Sand to 100-120 grit using NWFA approved methods.
- Screen with a 100-120 grit screen.
- Remove all sanding dust from the floor by thoroughly vacuuming and tacking with a dry Glitsa Tack Mop.
- Refer to directions on Glitsa Gold Seal Stains for application procedures and dry times.
- After stains are thoroughly dry, apply seal coat. Note: Quick Dry Sealer and Poly 500 are not recommended for use over pastel stained floors. Use Glitsa TruSeal waterborne sealer and GlitsaMax 2 waterborne finish.
Application Instructions:
For best results, apply Glitsa Poly Quick Dry Sealer at temperatures between 60º – 70º F. (15.6 – 21.1º C.), and 40%-60% R.H. High humidity, or low temperatures will extend dry times. Make sure to have indirect ventilation while applying Glitsa Poly Quick Dry Sealer.
Stir Glitsa Poly Quick Dry Sealer thoroughly. Apply Glitsa Poly Quick Dry Sealer by using a clean lambswool or synthetic applicator, or a lambswool roller.
Start by pouring a 3”-5” puddle of Glitsa Poly Quick Dry Sealer with the grain of the wood, from wall-to-wall. Apply Glitsa Poly Quick Dry Sealer with the grain of the wood, from wall-to-wall. Use a cut-in pad or a T-bar to feather out turns.
Maintain a 3”-5” puddle at all times, as this will help to ensure even coverage, and a uniform final appearance. When Glitsa Poly Quick Dry Sealer has dried to the touch, ventilate premises, while maintaining temperatures of 60º – 70º F. (15.6º – 21.1º C.). Optimum air quality is achieved through aggressive ventilation.
Once dry, abrade with a conditioning pad and 180 grit or finer sanding strips. Vacuum carefully, and tack with water or mineral spirits using a Glitsa Tack Mop.
A first coat of Glitsa Poly 500 may now be applied. Follow directions on finish label.
Apply no more than two coats in a 24-hour period.
Clean equipment immediately after applying finish with mineral spirits or compliant thinner.
Read Safety Data Sheet (SDS) and Label Precautions before using this product.
Physical Properties
| Oil Modified Polyurethane | Quick Dry Sealer | Poly 500 |
| Cast | Amber | Amber |
| Clarity (in can) | Clear | Clear |
| Solids by Weight | 38.4% | 41.1 – 44.0% |
| Viscosity (#2 Zahn – seconds) | ~22 sec | 28 sec |
| Flash Point (deg F.) | >100 | >100 |
| Pounds/Gallon | 7.13 | 7.18 |
| Dry Time to Touch*** | 2 hour | 4 hours |
| Recoat Time | 4 hour | 8 hours |
| Full Cure | 7 days | 7 days |
| Sq.Ft. Coverage/Gallon | 500-600 | 500-600 |
| VOC grams/liter | < 550 | < 550 |
| Sheen* – Gloss | n/a | >85 |
| Sheen* – Semi-Gloss | n/a | 42-53 |
| Sheen* – Satin | n/a | 27-33 |
| Sheen* – Matte | n/a | 8-12 |
*60 Degree Gloss Meter
***@70 deg F, 50% RH
